SilverStone SST-ML06B Installation Guide

ML05ML06

811.12.將多功能磁架裝回機殼Reinstale el bracket multipropósito de nuevo en el chasis.将多功能磁架装回机壳简体中文繁體中文Reinstall the multipurpose bracket back into the chassis.

13.Vuelva a poner la cubierta superior en la carcasa y fíjela con tres tornillos para completar la instalación.Place the top cover back onto the case

Power switch and reset switch installation guide:Please refer to the motherboard manuals for the motherboard’s “Front Panel Connector” or “System Pane

Connector definitionPlease refer to the motherboard manuals for the motherboard’s “Front Panel Connector ” or “System Panel Connector” pin definition.

Front I/O connector guideBelow are the front I/O connectors pin definition, please also check your motherboard manual to cross reference with motherb

Component size limitationsCPU Cooler height limitation will vary depending on the component installed on the multipurpose bracket. Please refer to the

Component size limitationsThe ML06 supports standard SFX power supply with a 100mm depth.(2) Power supply limitations Der ML06 unterstützt SFX-Standa

Component size limitationsThe ML06 only supports slim“slot-loading” optical drives.Below are examples of 12.7mm and 9.5mm optical drives.(4) Optical

ML06 只能使用吸入式薄型光碟機。以下是12.7mm與9.5mm的光碟機範例供您做參考。ML06 只能使用吸入式薄型光驱。以下是12.7mm与9.5mm的光驱范例供您做参考。ML06はスリムタイプ「スロットローディング」光学ドライブのみをサポートします。下図は、12.7mmと9.5mmの光学ドライ

Upgrade and maintenance Located near the first expansion slot of the case, there is a cutout in the shape of a VGA (D-sub) connector, this is designed

ML06 can not support graphics card that comes with dual fixed low profile slot bracket.Das ML06 nimmt keine Grafikkarten auf, die zwei Slotblechaussch

1. Используйте шестигранную отвертку для снятия разъема стандартного размера графической карты.2. Сделайте паз VGA (D-sub) в корпусе и установите разъ

Warranty InformationThis product has a limited 1 year warranty in North America and Australia. For information on warranty periods in other regions,

G11220140

Product OverviewSpecificationModel No.MaterialMotherboardDrive BayCooling SystemExpansion SlotFront I/O PortPower SupplyExpansion CardNet WeightDimens

2TOP FILTER (FF143)TOP COVERMULTIPURPOSE4+IN-1BRACKETLOW PROFILE EXPANSION CARD(NOT INCLUDE)MOTHERBOARD(NOT INCLUDE)8025 FAN X2 (NOT INCLUDE)USB 3.0 X

1.2.先用螺絲起子鬆開三顆螺絲,再取下上蓋板. 鬆開中支架2顆螺絲,卸下中支架松开中支架2颗螺丝,卸下中支架先用螺丝起子松开三颗螺丝,再取下上盖板. 简体中文繁體中文简体中文繁體中文Unscrew the three screws from the rear of the chassis then

4.安裝電源供應器,請注意此機殼的正反裝設計, 如果使用銀欣的SFX電源,8cm風扇請朝上(關於電源供應器長度規格,請參考元件尺寸限制)ケースに電源をインストールします。ケースは2つの異なる方向での電源設置をサポートしていることにご注意ください。SilverStone製SFX電源を使用される場合、8

5.6. 拆卸多功能磁架拆卸多功能磁架简体中文繁體中文Remove the multipurpose bracket. Снимите многоцелевой кронштейн. Nehmen Sie die Mehrzweckhalterung heraus. 다목적 브래킷을 분리합니

7.8.我們建議你在安裝主機板之前即開始準備整線動作。包含風扇電源線, PSU 24Pin接線 , CPU ATX 4Pin/EPS 8Pin接線,Front Panel Connectors與Front I/O Connectors。我们建议你在安装主机板之前即开始准备整线动作。包含风扇电源线,

9.7移除介面卡檔片,安裝介面卡Instale y fije las tarjetas de expansión necesarias.移除适配卡档片,安装适配卡简体中文繁體中文Install and secure required expansion cards.Установите и закр